Home and Auto Any Advice From the Floor Guys

**BigRichard** · 10-14-2022, 02:28 PM

I am starting to tear up my bathroom which had marble flooring. I have done ceramic tile before and it seems like they used way more thinset than what was needed here. It seems to be cracking off in little bits as I get my pry bar to get underneath of it instead of the entire tile coming up. Any suggestions here? Will I be able to get up that thinset off of that cement board? I was almost thinking that I will need to cut up all of that cement board too and replace with new for the tile I am going to put down.

Otter · 10-14-2022, 03:22 PM

I recently did a similar job and instead of trying to chip away (how I initially started) I wound up cutting the floor into 12x12 inch section with a circular saw down to the floor joists then took it out and laying a whole new foundation in the room.

That's gonna be a bitch chip away. It will still be a PITA on the edges but in the long run it saved me time and money.

Sassy Squatch · 10-14-2022, 03:24 PM

I'd just go all the way down to the joists/subfloor and start it over again. Might as well in case something's slipped your notice and got wet and rotten.

Monty · 10-14-2022, 03:38 PM

Quote:

Originally Posted by Superturtle

I'd just go all the way down to the joists/subfloor and start it over again. Might as well in case something's slipped your notice and got wet and rotten.

I'd recommend the same unless you want to hire Superturtle's Dad.

God of Thunder · 10-14-2022, 03:26 PM

So I just did this to the whole kitchen and it was a freaking nightmare. I went and bought 3 Multi-Tools from Home Depot like this - with the horizontal blades....

https://www.homedepot.com/p/Milwauke...6-20/204463218

Made the job a heck of a lot easier.

Sassy Squatch · 10-14-2022, 03:27 PM

Quote:

Originally Posted by God of Thunder

So I just did this to the whole kitchen and it was a freaking nightmare. I went and bought 3 Multi-Tools from Home Depot like this - with the horizontal blades....

https://www.homedepot.com/p/Milwauke...6-20/204463218

Made the job a heck of a lot easier.

My dad abuses the **** out of that. It's his solution to damn near every problem now.

**Rain Man** · 10-14-2022, 03:47 PM

Quote:

Originally Posted by God of Thunder

So I just did this to the whole kitchen and it was a freaking nightmare. I went and bought 3 Multi-Tools from Home Depot like this - with the horizontal blades....

https://www.homedepot.com/p/Milwauke...6-20/204463218

Made the job a heck of a lot easier.

What is that? What does it do?

**BigRichard** · 10-14-2022, 03:49 PM

Can I just use a circular saw to cut that into 12inch squares? That won't hurt the circular saw at all(with the right blade)? I know it will be dusty as hell.

KCUnited · 10-14-2022, 03:51 PM

****! Just found out my son posts on CP

Warpaint69 · 10-14-2022, 03:58 PM

Quote:

Originally Posted by BigRichard

Can I just use a circular saw to cut that into 12inch squares? That won't hurt the circular saw at all(with the right blade)? I know it will be dusty as hell.

I'd do that. Set your depth on the saw and go. Yes the dust will be awful!

Otter · 10-14-2022, 04:04 PM

Quote:

Originally Posted by BigRichard

Can I just use a circular saw to cut that into 12inch squares? That won't hurt the circular saw at all(with the right blade)? I know it will be dusty as hell.

Oh you're going to go through the blade depending on the size of the room, maybe several.

Fan pointing out the window for dust and a clean up afterwards. It's messy.

TLO · 10-14-2022, 04:00 PM

I prefer Five Guys.

BryanBusby · 10-14-2022, 04:54 PM

Quote:

Originally Posted by Hank Hill

I prefer Five Guys.

That's a lot of guys at once.

**ptlyon** · 10-14-2022, 07:47 PM

Quote:

Originally Posted by BryanBusby

That's a lot of guys at once.

He can take it

**notorious** · 10-14-2022, 04:01 PM

Rotary hammer set on jackhammer motion ONLY.

Flat shank.

It takes time, but it will work.

Get gloves so you don't cut the hell out of your hands. Only fill the trashcan 1/3rd full or it will be too heavy to dump.

The rotary hammer does a jackhammer motion. Let it do the work, don't force it. You'll figure it out after some practice.

10-14-2022, 02:28 PM	Topic Starter
BigRichard Buddy Christ is a Chiefs fan Join Date: Nov 2008 Casino cash: $-1940454	Any Advice From the Floor Guys I am starting to tear up my bathroom which had marble flooring. I have done ceramic tile before and it seems like they used way more thinset than what was needed here. It seems to be cracking off in little bits as I get my pry bar to get underneath of it instead of the entire tile coming up. Any suggestions here? Will I be able to get up that thinset off of that cement board? I was almost thinking that I will need to cut up all of that cement board too and replace with new for the tile I am going to put down.
Posts: 11,341

10-14-2022, 03:24 PM	#3
Sassy Squatch The man you could post like. Join Date: Oct 2010 Casino cash: $-1480345	I'd just go all the way down to the joists/subfloor and start it over again. Might as well in case something's slipped your notice and got wet and rotten.
Posts: 42,110

10-14-2022, 03:26 PM	#5
God of Thunder Trained to reign as the one. Join Date: Nov 2006 Location: Los Angeles, CA Casino cash: $8849344	So I just did this to the whole kitchen and it was a freaking nightmare. I went and bought 3 Multi-Tools from Home Depot like this - with the horizontal blades.... https://www.homedepot.com/p/Milwauke...6-20/204463218 Made the job a heck of a lot easier.
Posts: 1,489

10-14-2022, 03:49 PM	#8
BigRichard Buddy Christ is a Chiefs fan Join Date: Nov 2008 Casino cash: $-1940454	Can I just use a circular saw to cut that into 12inch squares? That won't hurt the circular saw at all(with the right blade)? I know it will be dusty as hell. __________________ "You know, they lay down with their ugly wives in front of their ugly children and just look at their loser lives and then they look at me and say, "I CAN'T PROCESS IT!" Well, no, and you never will. Stop trying. Just sit back and enjoy the show .... You know?" Carlos Irwin Estevez
Posts: 11,341

10-14-2022, 03:51 PM	#9
KCUnited Cheat Death Join Date: Nov 2007 Location: Land of Drincoln Casino cash: $-1651756	****! Just found out my son posts on CP
Posts: 37,029

10-14-2022, 04:00 PM	#12
TLO Life is changing.. Join Date: Jul 2012 Location: NW Missouri Casino cash: $-2620000	I prefer Five Guys.
Posts: 43,123

10-14-2022, 04:01 PM	#15
notorious Supporter Join Date: May 2005 Location: Who knows? Casino cash: $-1004116	Rotary hammer set on jackhammer motion ONLY. Flat shank. It takes time, but it will work. Get gloves so you don't cut the hell out of your hands. Only fill the trashcan 1/3rd full or it will be too heavy to dump. The rotary hammer does a jackhammer motion. Let it do the work, don't force it. You'll figure it out after some practice.
Posts: 88,591